logo
Shandong Jingwei Steel Manufacturing Co., Ltd.
Email admin@sdjws.com TEL: 86-13501001767
Home > PRODUCTS > Steel Pipe Steel Tube >
ERW Welded Carbon Steel Pipe ASTM A53 Gr.B OD 114mm Wall 4mm 12m Length for Structure
  • ERW Welded Carbon Steel Pipe ASTM A53 Gr.B OD 114mm Wall 4mm 12m Length for Structure
  • ERW Welded Carbon Steel Pipe ASTM A53 Gr.B OD 114mm Wall 4mm 12m Length for Structure

ERW Welded Carbon Steel Pipe ASTM A53 Gr.B OD 114mm Wall 4mm 12m Length for Structure

Place of Origin China
Brand Name Jingwei
Certification ISO 9001:2015, ASTM A53, EN 10219 on request
Model Number JW-ERW-A53
Product Details
Welding:
High Frequency ERW, Weld Seam Normalized
OD / WT:
114.3 Mm X 4.0 Mm
Length:
12 M, Tolerance 0 To +20 Mm
Highlight: 

ERW Welded Carbon Steel Pipe

,

ASTM A53 Gr.B Steel Pipe

,

12m Structural Steel Pipe

Payment & Shipping Terms
Minimum Order Quantity
5 tons
Price
USD 560 - 690 per ton FOB Tianjin
Packaging Details
Bundled by size, steel straps, no caps unless requested
Delivery Time
7 - 15 days after deposit
Payment Terms
T/T 30% deposit, balance against B/L copy; L/C at sight
Supply Ability
8000 tons per month
Product Description

For structural work the pipe does not need a seamless wall, it needs a weld that will not open under load and a price that keeps the project competitive. This ERW pipe is formed from hot rolled coil and welded by high frequency induction at the longitudinal seam, with the weld zone normalized in line so the heat affected area does not become a hard, brittle strip. It is supplied to ASTM A53 Gr.B in 114.3 mm outside diameter with a 4.0 mm wall and a 12 m length, a combination that suits scaffolding, racking, handrail, light piling and general fabrication.

The economic case is straightforward. ERW pipe uses coil rather than billet, so for the same outside diameter and wall it is typically 8 to 12 percent cheaper than seamless, and it is available in longer lengths. The trade off is that the seam must be sound and the pipe must be straight enough to fabricate without forcing. We address that with in-line weld seam annealing, eddy current testing of the weld on request, and a straightness limit of 1.5 mm per metre before the pipe is cut to length.

Key Features
  • High frequency ERW with normalized seam: the weld and its heat affected zone are normalized in line to restore toughness along the seam.
  • Cost efficient versus seamless: coil-based production keeps the ton price lower for structural and low pressure service.
  • 12 m length for fewer joints: longer lengths reduce welding, cutting and handling on the fabrication floor.
  • Square cut and deburred ends: ends cut to within 1 mm squareness and deburred so the pipe sits flat in jigs.
  • Consistent roundness: sizing and straightening stands hold ovality within specification for reliable clamping.
  • Weld tested on request: eddy current or ultrasonic inspection of the seam can be added for critical structures.
  • Available in black or pre-painted: bare black, oiled, or primer coated for buyers who paint after fabrication.
Technical Specifications
Parameter Specification
Product ERW welded carbon steel pipe
Standard ASTM A53 Gr.B, EN 10219, GB/T 3091
Outside diameter 21.3 mm - 508 mm
Wall thickness 1.5 mm - 12 mm
Length 6 m, 12 m, or cut to order
Grade Gr.B, Q235B, Q345B, S235JR, S355JR
Tensile strength 415 MPa minimum (Gr.B)
Yield strength 240 MPa minimum (Gr.B)
Weld High frequency induction, seam normalized
Ends Plain square cut, beveled on request
Surface Black bare, oiled, or primer painted
Test Hydrostatic, eddy current on request
Applications

Typical applications are steel racking uprights and beams, mezzanine columns, temporary works and formwork props, guardrail and handrail, pipe piles for low load foundations, and frames for agricultural sheds and carports. It is also widely used for low pressure air, water and slurry lines where the operating pressure stays under about 1.6 MPa.

If the structure is dynamically loaded, welded into a pressure boundary, or will be galvanized after fabrication, raise it with us before ordering. Galvanizing after welding requires the seam to be fully welded shut and vent holes to be drilled, and some fabricators prefer seamless pipe for that reason. We would rather flag this at quotation than have a container rejected at the galvanizer.

Inspection, Documentation and Packaging

Each coil is checked for grade and thickness on receipt, and the strip is trimmed before forming so the weld edges are clean. After welding, the pipe passes sizing, straightening, cut to length and end facing. Inspection covers outside diameter, wall thickness at both ends, straightness, weld bead condition, and a hydrostatic test at the pressure specified for the ordered wall.

Bundles are strapped with steel banding and stacked in a pattern for container loading, with wooden dunnage between layers to prevent abrasion during the sea voyage. Ends are left open unless caps are requested, because trapped moisture inside a capped ERW pipe is a common cause of white rust claims on arrival.

Buyer Questions We Answer Before Ordering

Can the pipe be galvanized after I weld the frame? Yes, but the seam must be continuous and vent holes drilled. Tell us the fabrication plan and we will advise on venting and on whether a seamless pipe is more suitable.

What wall thickness tolerance applies? Wall thickness is controlled to plus or minus 10 percent of nominal, with outside diameter held to ASTM A53 tolerance.

Can you supply shorter cut lengths for racking? Yes, we cut to any length from 1 m upward, and we can deburr and bundle by cut length for direct feeding to your line.

Contact Us at Any Time

86-13501001767
Dongchangfu District Industrial Park, Liaocheng City, Shandong Province, China
Send your inquiry directly to us